某340矫直机上辊快开机构裂纹原因分析及预防措施

340管线矫直机是太原重工成熟产品,在国内占有较大市场,并出口印度、印尼、缅甸、埃及等国际市场。出口印度矫直机在质保期内出现主缸裂纹问题,为探明问题原因并杜绝类似情况发生,快开机构设计静强度分析、疲劳强度分析及生产加工过程等方面探查裂纹原因并提出几点预防措施。     

Strength and dilatancy behaviors of deep sands in Shanghai with a focus on grain size and shape effect

With rapid development of infrastructures like tunnels and open excavations in Shanghai, investigations on deeper soils have become critically important. Most of the existing laboratory works were focused on the clayey strata up to Layer 6 in Shanghai, i.e. at depth of up to 40 m. In this paper, Layers 7, 9, and 11, which were mostly formed of sandy soils at depth of up to 150 m, were experimentally investigated with respect to physico-mechanical behaviors. The stress–strain behaviors were analyzed by the consolidated drained/undrained (CD/CU) triaxial tests under monotonic loading. One-dimensional (1D) oedometer tests were performed to investigate the consolidation properties of the sandy soils. Specimens were prepared at three different relative densities for each layer. Also, the micro-images and particle size analyzers were used to analyze the shape and size of the sand grains. The influences of grain size, density, and angularity on the stress–strain behaviors and compressibility were also studied. Compared to the other layers, Layer 11 had the smallest mean grain size (D₅₀), highest compressibility, and lowest shear strength. In contrast, Layer 9 had the largest mean grain size, lowest compressibility, and highest shear strength. Layer 7 was of intermediate mean grain size, exhibiting more compressibility and less shear strength than that of Layer 9. Also, the critical state parameters and maximum dilatancy rate of different layers were discussed.     

基于3D打印技术复制砂浆节理的剪切试验及峰值抗剪强度模型

为进一步研究节理三维形貌特征与节理峰值抗剪强度的关系,首先采用巴西劈裂试验获取了自然劈裂岩石表面,通过三维扫描技术获取了节理面形态的高精度点云,通过逆向建模得到了自然岩石表面的立体模型,结合3D打印技术制作出了与自然岩石表面一致的PLA模具,以3D打印获得的底模通过水泥砂浆浇筑了含有自然结构面形貌的相似节理面试样。PLA模具与复制材料差异较大,复制材料在凝结过程中不易与PLA模具黏结,进而使脱模过程较为方便,不会破坏节理面。同时PLA模具可重复进行相似材料复制工作,具有可重复使用的优点。然后进行了具有5组形貌面的20个水泥砂浆节理面在4种不同法向荷载情况下的结构面剪切试验,得到了结构面剪切位移-荷载曲线。研究了结构面峰值抗剪强度、峰值位移、剪切刚度影响因素。节理经过剪切后形貌面出现不同程度的磨损,其磨损范围与等效高差分布范围基本一致,并且在等效高差为剪断破坏模式且成片的区域磨损较为严重。在新粗糙度指标基础上提出了新的峰值抗剪强度模型,经试验对比显示出新模型的有效性。在新模型基础上提出了一个简化模型。对比发现新模型简化后其计算精度较新模型有所降低但由于所需参数减小计算较为方便,新模型简化结果精度虽然有所下降但是还是比Barton公式精度高。     

Excellent Mechanical and Transparency Properties of Cationic Waterborne Polyurethane Films Modified by Boehmite Sol

The strategies for nanosol from metal alkoxide have enabled production of ultratransparent and mechanically robust polymer nanocomposites at extremely high loading. Herein, a simple approach to fabricate high‐performance polyurethane‐based nanocomposites via unmodified boehmite nanoparticles is reported. Evaluating their physical properties, the uniform dispersion of boehmite in the matrix caused nanocomposites retains ultrahigh transparency. Hydrogen bonding and intermolecular entanglement between boehmite and polyurethane brings about the mechanical properties of the nanocomposites material enhanced, i.e., strength, stiffness, and toughness. Optimized strength, stiffness, and toughness of Boehmite/Cationic waterborne polyurethane at 40 wt% (BNC40) are up to 58.1 MPa, 1096.7 MPa, 249.5 MJ m^?3, respectively. Furthermore, the feasibility and mechanism of polymer strengthening and toughening by inorganic rigid nanoparticles is explored from the aspects of crystallinity and micromorphology.     

机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

硅渣和玻璃粉直接烧结制备多孔材料的气孔结构与力学性能

以硅渣和玻璃粉为原料,采用粉体直接烧结法制备多孔材料,研究了烧结温度(700~900℃)、烧结时间(15~120min)和升温速率(10~100℃·min^-1)对多孔材料表观密度、气孔率、物相组成、抗压强度的影响。结果表明:气孔结构均匀性随烧结温度的升高而降低;表观密度随烧结温度的升高先减小后增大,随保温时间的延长而增大,随升温速率的增大而减小,气孔率的变化趋势与表观密度的相反;多孔材料的主要物相为玻璃相和硅、SiC、SiO2、Ca2Al2SiO7等结晶相,且结晶度随烧结温度的升高而降低;抗压强度随烧结温度的升高呈先增大后减小的趋势;当烧结温度为750℃,升温速率为30℃·min^-1,烧结时间为30 min时,多孔材料的主晶相为硅和Ca2Al2SiO7,抗压强度最大(1.60MPa),表观密度为0.43g·cm^-3,气孔率为80%。     

Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.